Hello everyone! Today, the Voopoo Vinci 2 is the perfect vaping opportunity. The device received an attractive appearance, small size and is convenient for an active lifestyle. Works on old PnP evaporators that have proven themselves to be excellent.

Equipment
Vinci 2, two interchangeable coils, charging cable, instructions.

Information

Voopoo Vinci 2 kit is made of zinc alloy. Available in 5 colors: Velvet Blue, Pine Gray, Dazzling Line, Carbon Fiber, Neon. Equipped with GENE.AI 2.0 board up to 50 watts with support from 0.15 ohm. Works on familiar PNP evaporators.

Technical specifications
Output power: 5 to 50 watts,
Supported resistance: 0.15 to 3 ohms,
Battery capacity: 1500 mAh,
Operating modes: VW, Smart,
Maximum charge current: 2 A.

Dimensions

Height: 106 mm,
Width: 28 mm,
Thickness: 27 mm,
Weight: 114 g.

Cartridge, evaporators
The mouthpiece remained built-in - the same wide and relatively thick, but with a different duct opening.

The body of the tank is made of transparent plastic to make it easier to track the level of the remaining liquid. The filler hole is located at the bottom on a small rim.

The tank holds 6.5 ml. For work, they did not make new coils, for which thanks - the usual PNPs are used.

The set includes VM1 for 0.3 Ohm and TM2 for 0.8 Ohm. Well, the usual serviced bases are also suitable here. Magnets are used to hold the tank.

Battery pack
The design remains recognizable for the Vinci line, but with minor improvements.

The body is made of zinc, but this time it received a matte finish. Also, the decorative insert is located only on the backside, and not on the sides.

At the top of the compartment, there are magnets, a contact group and a tightening sensor.

On the side we see another improvement - the airflow control has been added in the form of a lever.

the lever allows you to adjust the tightening

On the other side on top is the Type-C port for charging. But the front panel was left from glossy plastic.

It houses around Fire, a color screen and adjustment buttons. The Fire got a little stroke with a nice click, and the settings buttons are slightly recessed into the body.

Below we see certificates and a rubber spacer so that they stand more confidently on the table underneath. A 1500 mAh battery is installed inside.

Board capabilities
The already familiar GENE.AI 2.0 is used as aboard. To enter the menu, we hold down the plus and minus. You can choose between the usual Variable and Smart mode, and also change the theme.

To select the mode of operation from tightening or from the button - press FIre three times. To block all buttons, a combination of plus and Fire is used, and to collect traction - Fire and minus. There is also a screen flip.

Otherwise, the board delivers up to 50 watts with support from 0.15 ohms. The charge current will be 2 A. But the pastry mode has not been added.

Operation and conclusions
The drip tip was not the most convenient. He's still pretty fat. There is a lot of space on top, so it would be possible to make the top filling and put the 510 formats.

There are no complaints about the volume, 6.5 ml will last for a long time. Plus, it will also go for using old coils, which can be bought in any vape shop.

The cartridge itself keeps well in the compartment. Evaporators don't leak much. The battery pack is well assembled. But the painting leaves much to be desired - it quickly scratches, and small chips appear.

Vinci 2 we used carefully, so our sample chips can not see, can not be said about Vinci 2 the X . Photo for the attention below.

left Vinci 2X, showing signs of abrasion)

Thanks for adjusting the airflow, but the protrusion of the lever could have been made smaller. The board is familiar, so the pros and cons remain the same - the control is convenient, but all buttons are locked at once, and the chip does not produce more than 4.2 Volts.

Well, the screen has become a little dimmer than the first Vinci. According to the thrust sensor, it is not very fast when the airflow is fully open. But with an overlap of about half, the situation improves markedly. Therefore, the auto-traction mode is more suitable for tight tightening.

In general, we get a slightly updated Vinci 40w - you can use it, but a more detailed revision was expected. And so far there is no adapter with a 510 connector, which is a little strange. Therefore, it makes sense to change to a new version - if you really need an accurate adjustment of the airflow, or the old battery no longer holds a charge.

Cons and pros
Cons:

- not the most comfortable mouthpiece,
- dull screen compared to previous versions,
- coating weak in durability

Pros:

- build quality,
- availability of airflow control,
- easy-to-operate board,
- use of familiar coil,
- large volume of the tank